Steel Products

With more than 20 years manufacture experience, TBN not only shared 2000000 tons steel with customers from more than 70 countries, but also devoted to be the most professional steel supplier and biggest stockist in China.

  1. Home > Steel Grade > 1 8918 carbon steel material

1 8918 carbon steel material

Description: EN 1.8918 (P460NL2) Steel :: MakeItFromThe graph bars on the material properties cards below compare EN 1.8918 steel to: EN wrought alloy steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A halffull bar means it's 50% of the highest, and so on.

Related Steels Products

  • 1.8918 steel Steel Grades

    1.8918 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join Supplier[email protected]

  • 1.8918 DIN :Total Materia

    1.8918, DIN, DIN EN 10028 3, Flat products made of steels for pressure purposes Part 3Weldable fine grain steels, normalized, DIN 17178, Welded circular tuber of fine grain steels for special requirements; technical delivery conditions, DIN 17179, Seamless circular tubes of fine grain steels for special requirements; technical delivery conditions, DIN EN 10216 3, Seamless steel tubes for

  • 1.8918 Steel CCT or TTT Diagram

    Carbon Steels Carburizing Steels Cast Irons Tools Steels Vanadium Steels Welding Steels White Cast Irons Help Home. 1.8918 Steel Steel name1.8918 Steel name of producersP460NL2 DIN EN 10028 3:2003 09 Germany Applications specifically suggested for material described herein are made solely for the purpose of illustration to enable

  • SUS430 steel

    Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. SUS430 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

  • EN 10028 2 P265GH Weld Neck Flange,P265GH Plate Flanges

    P265GHis a weldable pressure vessel and boiler steel grade used by the worlds industrial fabricators. The material, which is ideally suited for elevated temperature service, is commonly found in the oil & gas, petrochemical and chemical industry. This European standard grade steel has replaced the BS1501 and DIN17155 specification.

  • Bethlehem Steel ASTM A678 Grade C >1 1/2 to 2 in. thick

    >1 1/2 to 2 in. thick, steel plate, Carbon grade for plates made to a fine grain practice. The plate is heat treated by quenching and tempering to develop the high strength levels. The steel has high notch toughness. It is used in demanding

  • Buy Tool Steel Rectangle Bar D2 Online

    Tool Steel Rectangle/Flat Bar D2 is a high carbon, air hardening tool steel that provides good resistance to wear. D 2 provides a good blend of toughness, strength, and affordability. Refine search Start New Search. Sort by Displaying 1 Find Your Material Quickly

  • STEEL REPAIR SLEEVE RELI SLEEVE Manufacturer

    Steel Repair Sleeves can be used as pads or cradles for above ground piping, drain tile supports and patches (segments in 90° and 180° arcs, from 6 inches to 10 feet in length are available as specials). Each Steel Repair Sleeve has standard bevels with a back up strip and material certifications. Sleeve ends are square cut.

  • Strength Of Steels

    BS EN 10027 1:1992 Designation systems for steel. Steel names, principal symbols . This is a steel material designation system based on names. These names consist of alpha numerical characters and define two main groups of steels Steels Designated On The Basis Of

  • Overview of materials for Low Alloy Steel

    Overview of materials for Low Alloy Steel, This property data is a summary of similar materials in the MatWeb database for the category "Low Alloy Steel". Each property range of values reported is minimum and maximum values of appropriate MatWeb

  • EN 10028 Flat Products Made of Steel for Pressure Purpose

    EN 10028 Flat Products Made of Steel for Pressure Purpose. 1.8918 P255NL21.1106 EN 10028 Stainless Steel Flat Products Made of Steel for Pressure Purpose 2. EN 10028 7 Chemical Composition of Stainless Steel Flat 3. EN 10028 7 Mechanical Properties for Stainless Steel.

  • Seamless & Welded Fittings Steel DIN / EN OSMETALL

    We deliver from stock and warehousing as well as directly from the mill.

  • Steel fiber Continental

    MATERIAL. Cold drawn low carbon steel wire, without coating, GOST 3282, tensile strength of 900 1450 N/mm2. Other geometrical sizes can be made on the concordance with a customer's order. PACKING. Into cardboard boxes of 25 kg, on 1200x1000 mm wood pallets.

  • Forged rings N STEEL

    This website uses cookies to ensure you get the best experience on our website. More info

  • Stainless Steel Plate 310 Distributor, Source for

    Our heat treatable steel according to DIN EN 10083 1 and 2 comprises steel types used in mechanical engineering and suitable for tempering due to their chemical composition. Case hardening steel according to DIN EN 10084 covers steel types of relatively low carbon content, destined for carbonising or carbo nitrating with subsequent tempering.

COMPANY INFORMATION

Note: If you're interested in the 1 8918 carbon steel material, please submit your requirements and contacts and then we will contact you in two days. We promise that all your informations won't be leaked to anyone.

Copyright © 2019.TBN Steel All rights reserved.  sitemap